Mr-Glass Sliding & Patio Doors Nationwide

Mr-Glass Sliding & Patio Doors: The Woodland Hills Owner’s Guide

We stock and install Mr-Glass-compatible sliding and patio doors throughout Woodland Hills, with most complete door replacements running $1,800 to $4,600 installed depending on size, glass package, and frame condition. Same-week scheduling is typical for stock door configurations, and we carry the most common Mr-Glass rollers, handles, and lock sets on the truck for repair work that doesn’t require a full door swap. Most Woodland Hills homeowners discover they need us when the door starts grinding against its track, the handle stops latching, or the panel suddenly feels like it weighs twice as much as it did last month. That heaviness is usually the first real warning that rollers are done, and in the west Valley’s dry, dusty conditions, we replace roller sets on Mr-Glass doors far more often than we replace the doors themselves.

Call (831) 508-3441

Which Mr-Glass Models This Applies To

Mr-Glass manufactures sliding patio doors in two primary series: the 600 Series (aluminum frame, single-pane or basic dual-pane) and the 700 Series (heavier aluminum frame with thermally broken profiles and low-E glass options). The 700 Series doors are far more common in Woodland Hills homes built after the mid-1990s, especially in the neighborhoods east of Topanga Canyon Boulevard and the newer tracts near Warner Center. If you’re not sure which series you have, look at the corner of the glass panel from inside: Mr-Glass stamps the series number into the aluminum frame spacer between the glass panes, usually in the bottom corner. The stamp is small but readable with a flashlight.

One compatibility gotcha worth knowing: Mr-Glass roller assemblies are not universal across their own product line. The 600 Series uses a single-wheel roller cartridge with a 7/16-inch mounting slot, while the 700 Series uses a tandem dual-wheel cartridge with a 5/8-inch slot. They look nearly identical until you set them side by side, and we’ve seen more than a few homeowners order the wrong part online and strip the mounting screws trying to force it in. When we install an aftermarket roller, we use only cartridge assemblies that match the original mounting dimensions and wheel material, typically stainless-steel wheels on nylon hubs, which hold up better against Woodland Hills dust than the original nylon-on-nylon design Mr-Glass used in the 600 Series. For handles and lock sets, OEM Mr-Glass parts are still the right call because the screw hole spacing and latch throw depth are specific enough that aftermarket units rarely line up without drilling.

Signs Your Mr-Glass Sliding & Patio Doors Is Failing

• The door drags or grinds when you slide it. This almost always means the roller wheels have flat-spotted or seized. In Woodland Hills, fine dust from the Santa Monica Mountains gets into the track and chews through the nylon wheels over time. If you hear metal-on-metal squealing, the wheel has worn through entirely and is now riding on its axle.
• The handle lifts but the latch doesn’t retract. Mr-Glass mortise latches use a spring-loaded pawl that connects to the handle via a small metal cam. That cam wears down after about 8-10 years of daily use, especially on west-facing doors that get intense afternoon sun heating the aluminum. The handle moves freely, but the pawl stays locked in the jamb.
• The door panel sags or tilts forward when open. This points to a failed roller on the lower track, which usually means the other lower roller is doing all the work and is close behind. A sagging Mr-Glass panel puts uneven pressure on the top guide and can eventually gall the aluminum track itself, turning a $40 roller job into a track replacement.
• You can feel air coming through the door even when it’s fully closed. The compression weatherstrip along the interlock stile, the vertical edge where the two panels meet, loses its rebound after years of valley heat. Once the interlock seal goes flat, the door doesn’t just leak air; it stops sealing out the dry Santa Ana winds that push dust into every gap.
• Condensation forms between the glass panes. That’s a broken seal, period. Mr-Glass dual-pane units from the 700 Series are gas-filled and sealed at the factory. Once the seal fails, the insulating gas escapes and you’ll see fogging that comes and goes with temperature swings. The fix is glass replacement, not a door swap, but it’s not something to ignore because moisture inside the glazing pocket will eventually corrode the aluminum frame from the inside.

Replacement Cost & What’s Included

Here’s what Mr-Glass sliding and patio door work actually costs in Woodland Hills right now. A roller replacement on a single panel runs $180 to $340 including parts and labor, with the higher end covering both lower rollers and a track cleaning. Handle and lock set replacement lands at $220 to $420 depending on whether it’s a simple handle swap or a full mortise latch assembly. Glass replacement for a fogged dual-pane panel runs $450 to $950 per panel, driven primarily by glass size and whether low-E coating is required. Full door replacement, panel and frame, runs $1,800 to $4,600 installed, with the biggest variables being rough opening width, whether the home requires impact-rated glass, and whether the existing frame has water damage from a failed weatherstrip.

Every one of these numbers is a written price before we start, parts and labor, no change orders. If the repair fails within 365 days, parts and labor are covered by the Done Right Promise. We’ve never had to enforce it on a Mr-Glass roller job, but it’s in writing anyway. Woodland Hills homeowners should also know that a full door replacement on an exterior wall triggers a city permit requirement, and we pull the permit and schedule the inspection as part of the job. Some contractors skip this and save you $400. The inspector will catch it when you sell the house, and it won’t be a $400 fix then.

DIY or Call Us?

The honest answer: you can clean your own tracks and replace the weatherstrip yourself, and you should, because a clean track extends roller life meaningfully. But pulling a Mr-Glass panel out of its frame to swap rollers is where DIY goes sideways. The panel weighs 120 to 180 pounds depending on glass, and lifting it out requires removing the anti-lift blocks and angle-tilting the panel out of the top track. Get the angle wrong and the panel drops, which usually breaks the glass and sometimes breaks whatever is underneath it. The roller cartridges themselves are under no spring tension, so the mechanical part of the swap is straightforward, but the lift is not. If the door is dragging, we’d rather walk you through a quick visual check over the phone and then send a technician with the right rollers already loaded. Call (831) 508-3441 and describe what you’re hearing and feeling. We’ll tell you whether it sounds like a roller or a track issue before we ever schedule the visit.

How Long Do Mr-Glass Sliding Doors Last in Woodland Hills?

The frame and glass panels on a Mr-Glass door will hold up for 25 to 35 years in Woodland Hills conditions, but the wear components don’t get anywhere close to that. Roller assemblies typically fail between 8 and 15 years, with doors that face the prevailing dust path or get used heavily by kids and dogs trending toward the shorter end. Handles and latch mechanisms last 10 to 15 years. Weatherstrip needs replacement every 5 to 8 years, more often if the door gets full afternoon sun. The best way to stretch the panel life is keeping the bottom track vacuumed and replacing rollers at the first sign of grinding, because a seized roller becomes a track gouge faster than most people realize.

Can My Mr-Glass Door Be Repaired Instead of Replaced?

Most Mr-Glass sliding door problems are repairable, and we replace only when the frame itself is compromised. Rollers, handles, locks, weatherstrip, and glass panels are all serviceable components we replace regularly. The two situations that push toward full replacement are extensive aluminum corrosion from a long-term water leak, especially where the lower track meets the threshold, or frame damage from an impact that has pulled the corner welds apart. Even a badly gouged track can sometimes be repaired with an overlay track rather than replaced, but if the corrosion has eaten through the stile on a 600 Series door from the 90s, you’re better off putting the repair money toward a new 700 Series door with a thermally broken frame and modern glass.

How Long Does a Mr-Glass Sliding Door Repair Take?

A roller replacement on one panel takes 45 to 90 minutes on site, and we handle it same-visit because we carry the common Mr-Glass roller sizes on the truck. Handle and lock replacements run 30 to 60 minutes. Glass panel replacement, where we order the sealed unit to spec, typically runs 7 to 10 days from order to install, and the install itself takes about an hour. Full door replacement, including frame extraction, new frame installation, and stucco or drywall patch touch-up, runs one to two days depending on the transition and whether the home has aluminum or vinyl stucco details. Call us at (831) 508-3441 for a written estimate, and we’ll tell you which timeline applies to your specific door before you commit to anything.

Do You Stock Mr-Glass Parts in Woodland Hills, or Do You Order Them?

We stock the most common Mr-Glass wear parts on the truck: 600 and 700 Series roller cartridges, standard handle sets, mortise latch assemblies, and compression weatherstrip for the interlock and head track. Odd-size glass panels and specific finish-matched handles are ordered and usually arrive within a week. For Mr-Glass doors installed in Woodland Hills homes, we also keep PGT and CGI parts on the shelf, since many local homeowners have mixed-door configurations from different manufacturers. If you can read the series number off the glass stamp and describe the problem, we can usually confirm whether it’s a same-visit fix before the truck leaves the shop.

FAQs